# Boots with older image from emmc

DDR Version 1.15 20181010
In
Channel 0: DDR3, 933MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
no stride
ch 0 ddrconfig = 0x101, ddrsize = 0x20
pmugrf_os_reg[2] = 0x10006281, stride = 0x17
OUT
Boot1: 2018-08-06, version: 1.15
CPUId = 0x0
ChipType = 0x10, 210
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=14910MB
FwPartOffset=2000 , 100000
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
SdmmcInit=0 1
StorageInit ok = 67761
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
GPT 0x3190d20 signature is wrong
LoadTrust Addr:0x4000
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0x7658c
RunBL31 0x10000
NOTICE:  BL31: v1.3(debug):d98d16e
NOTICE:  BL31: Built : 15:03:07, May 10 2018
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    plat_rockchip_pmu_init(1151): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-106-g2d5da6a #1 Fri Oct 20 01:35:40 UTC 2017 aarch64)

INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.1

INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2014.10-RK3399-06 (Jul 11 2019 - 17:32:19)

CPU: rk3399
cpu version = 0
CPU's clock information:
    aplll = 816000000HZ
    apllb = 24000000HZ
    gpll = 800000000HZ
               aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
               aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
               hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
    cpll = 800000000HZ
    dpll = 928000000HZ
    vpll = 24000000HZ
    npll = 24000000HZ
    ppll = 676000000HZ
Board:	Rockchip platform Board
Uboot as second level loader
DRAM:  Found dram banks: 1
Adding bank:0000000000200000(000000003fe00000)
Reserve memory for trust os.
dram reserve bank: base = 0x08400000, size = 0x01200000
128 MiB
SdmmcInit = 0 20
storage init OK!
Using default environment

GetParam
Load FDT from resource image.
no key node
can't find dts node for fixed
usb bc: can find node by path: /dwc-control-usb/usb_bc
pmic:rk808
can't find dts node for pwm1
set pwm voltage ok,pwm_id =2 vol=1000000,pwm_value=33
Can't find dts node for fuel guage cw201x
can't find dts node for ec-battery
Can't find dts node for charger bq25700
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2018-11-10#1.09
empty serial no.
normal boot.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
failed to find panel driver
delay prepare[20] unprepare[0] enable[20] disable[0]
read logo on state from dts [1]
no fuel gauge found
[EDID] check header error
[HDMI] parse edid base block error-2
[EDID] check header error
[HDMI] parse edid base block error-2
[EDID] check header error
[HDMI] parse edid base block error-2
no edid message:use default vic config:16
hdmi_dev->video.vic is 16
rk lcdc - 1 dclk set: dclk = 148500000HZ, pll select = 0, div = 1
rockchip_panel_prepare: failed to find panel prepare funcs
hdmi_dev_config_video vic 16 color_output 1 color_output_depth 8
pixel clk is 148500000 tmds clk is 148500000
hsync_pol 1 vsync_pol 1
[HDMI] sucess output HDMI.
PHY PLL not locked: PCLK_ON=1,TMDSCLK_ON=1
rockchip_panel_enable: failed to find panel prepare funcs
failed to find display timing
Hit any key to stop autoboot:  0 
load fdt from resouce.
vendor read error!
Set oem_unlocked=0Secure Boot state: 0
kernel   @ 0x00280000 (0x010fd200)
ramdisk  @ 0x04bf0000 (0x005fe3c0)
bootrk: do_bootm_linux...
   Loading Device Tree to 0000000004600000, end 000000000461c187 ... OK
Add bank:0000000000200000, 0000000008200000
Add bank:0000000009600000, 0000000036a00000
WARNING: could not set reg FDT_ERR_BADOFFSET.

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.167 (root@Linux-Mint) (gcc version 6.4.0 (ctng-1.23.0-150g-FA) ) #1 SMP Fri Aug 23 18:42:44 MSK 2019
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03feea000 s46248 r8192 d31576 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 252936
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 console=ttyFIQ0 rw root=PARTUUID=614e0000-0000 rootfstype=ext4 rootwait root=/dev/mmcblk1p7 rw rootfstype=ext4 data=/dev/mmcblk1p8 consoleblank=0 mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(trust),0x00002000@0x00006000(misc),0x00006000@0x00008000(resource),0x00010000@0x0000e000(kernel),0x00010000@0x0001e000(boot),0x8B6000@0x00030000(rootfs),-@0x8E6000(userdata) storagemedia=emmc uboot_logo=0x02000000@0x3dc00000 loader.timestamp=2019-07-11_17:32:19 SecureBootCheckOk=0
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x3fe22000-0x3fe62000] (0MB) mapped at [ffffffc03fe22000-ffffffc03fe61fff]
[    0.000000] Memory: 980828K/1028096K available (10940K kernel code, 1332K rwdata, 3968K rodata, 1088K init, 1982K bss, 47268K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8008f20000 - 0xffffff8009030000   (  1088 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008b30000   ( 10944 KB)
[    0.000000]     .rodata : 0xffffff8008b30000 - 0xffffff8008f20000   (  4032 KB)
[    0.000000]       .data : 0xffffff8009030000 - 0xffffff800917d200   (  1333 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[    0.000000] ITS: allocated 65536 Devices @9600000 (psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GIC: using LPI property table @0x0000000009680000
[    0.000000] ITS: Allocated 1792 chunks for LPIs
[    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] CPU0: using LPI pending table @0x0000000009690000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.002146] Console: colour dummy device 80x25
[    0.002592] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.003588] pid_max: default: 32768 minimum: 301
[    0.004142] Security Framework initialized
[    0.004554] AppArmor: AppArmor disabled by boot time parameter
[    0.005156] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.005810] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.007171] Initializing cgroup subsys io
[    0.007569] Initializing cgroup subsys memory
[    0.008024] Initializing cgroup subsys devices
[    0.008460] Initializing cgroup subsys freezer
[    0.008892] Initializing cgroup subsys net_cls
[    0.009334] Initializing cgroup subsys perf_event
[    0.009792] Initializing cgroup subsys net_prio
[    0.010238] Initializing cgroup subsys pids
[    0.010685] ftrace: allocating 36618 entries in 144 pages
[    0.114240] sched-energy: Sched-energy-costs installed from DT
[    0.114811] CPU0: update cpu_capacity 401
[    0.115263] ASID allocator initialised with 32768 entries
[    0.118592] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.119963] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.121287] EFI services will not be available.
[    0.122702] Detected VIPT I-cache on CPU1
[    0.122733] CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.122768] CPU1: using LPI pending table @0x000000003e480000
[    0.122812] CPU1: update cpu_capacity 401
[    0.122815] CPU1: Booted secondary processor [410fd034]
[    0.123392] Detected VIPT I-cache on CPU2
[    0.123412] CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.123444] CPU2: using LPI pending table @0x000000003e4b0000
[    0.123471] CPU2: update cpu_capacity 401
[    0.123475] CPU2: Booted secondary processor [410fd034]
[    0.124018] Detected VIPT I-cache on CPU3
[    0.124036] CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.124069] CPU3: using LPI pending table @0x000000003e500000
[    0.124094] CPU3: update cpu_capacity 401
[    0.124097] CPU3: Booted secondary processor [410fd034]
[    0.124636] Detected PIPT I-cache on CPU4
[    0.124664] CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.124704] CPU4: using LPI pending table @0x000000003e530000
[    0.124741] CPU4: update cpu_capacity 1024
[    0.124744] CPU4: Booted secondary processor [410fd082]
[    0.125312] Detected PIPT I-cache on CPU5
[    0.125330] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.125367] CPU5: using LPI pending table @0x000000003e570000
[    0.125390] CPU5: update cpu_capacity 1024
[    0.125393] CPU5: Booted secondary processor [410fd082]
[    0.125478] Brought up 6 CPUs
[    0.137924] SMP: Total of 6 processors activated.
[    0.138378] CPU features: detected feature: GIC system register CPU interface
[    0.139071] CPU features: detected feature: 32-bit EL0 Support
[    0.139634] CPU: All CPU(s) started at EL2
[    0.140068] alternatives: patching kernel code
[    0.141838] devtmpfs: initialized
[    0.158693] DMI not present or invalid.
[    0.159356] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.160292] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.161395] pinctrl core: initialized pinctrl subsystem
[    0.162664] NET: Registered protocol family 16
[    0.168346] cpuidle: using governor ladder
[    0.174360] cpuidle: using governor menu
[    0.174745] Registered FIQ tty driver
[    0.175332] vdso: 2 pages (1 code @ ffffff8008b36000, 1 data @ ffffff8009034000)
[    0.176059] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.176853] DMA: preallocated 256 KiB pool for atomic allocations
[    0.201732] console [ttyFIQ0] enabled
[    0.201732] console [ttyFIQ0] enabled
[    0.202406] bootconsole [uart0] disabled
[    0.202406] bootconsole [uart0] disabled
[    0.203302] Registered fiq debugger ttyFIQ0
[    0.217858] vcc_lcd: supplied by vcc5v0_sys
[    0.239955] iommu: Adding device ff650000.vpu_service to group 0
[    0.240568] iommu: Adding device ff660000.rkvdec to group 1
[    0.241156] iommu: Adding device ff8f0000.vop to group 2
[    0.241713] iommu: Adding device ff900000.vop to group 3
[    0.242262] iommu: Adding device ff910000.rkisp1 to group 4
[    0.242843] iommu: Adding device ff920000.rkisp1 to group 5
[    0.243813] rk_iommu ff650800.iommu: can't get sclk
[    0.244503] rk_iommu ff660480.iommu: can't get sclk
[    0.245133] rk_iommu ff8f3f00.iommu: can't get sclk
[    0.245714] rk_iommu ff903f00.iommu: can't get sclk
[    0.246307] rk_iommu ff914000.iommu: can't get sclk
[    0.246887] rk_iommu ff924000.iommu: can't get sclk
[    0.247602] SCSI subsystem initialized
[    0.248261] usbcore: registered new interface driver usbfs
[    0.248799] usbcore: registered new interface driver hub
[    0.249346] usbcore: registered new device driver usb
[    0.249862] media: Linux media interface: v0.10
[    0.250286] Linux video capture interface: v2.00
[    0.250733] pps_core: LinuxPPS API ver. 1 registered
[    0.251184] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.252003] PTP clock support registered
[    0.252469] dmi: Firmware registration failed.
[    0.253878] Advanced Linux Sound Architecture Driver Initialized.
[    0.254933] Bluetooth: Core ver 2.21
[    0.255270] NET: Registered protocol family 31
[    0.255677] Bluetooth: HCI device and connection manager initialized
[    0.256241] Bluetooth: HCI socket layer initialized
[    0.256682] Bluetooth: L2CAP socket layer initialized
[    0.257143] Bluetooth: SCO socket layer initialized
[    0.257926] NetLabel: Initializing
[    0.258232] NetLabel:  domain hash size = 128
[    0.258617] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.259096] NetLabel:  unlabeled traffic allowed by default
[    0.260000] rockchip-cpuinfo cpuinfo: Serial		: afd601544d59a9f5
[    0.260965] clocksource: Switched to clocksource arch_sys_counter
[    0.300833] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.301777] NET: Registered protocol family 2
[    0.302611] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.303288] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[    0.304038] TCP: Hash tables configured (established 8192 bind 8192)
[    0.304676] UDP hash table entries: 512 (order: 3, 49152 bytes)
[    0.305251] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[    0.306010] NET: Registered protocol family 1
[    0.306725] RPC: Registered named UNIX socket transport module.
[    0.307266] RPC: Registered udp transport module.
[    0.307686] RPC: Registered tcp transport module.
[    0.308113] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.309350] Trying to unpack rootfs image as initramfs...
[    0.598672] Freeing initrd memory: 6136K
[    0.599541] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.600382] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.603950] audit: initializing netlink subsys (disabled)
[    0.604491] audit: type=2000 audit(0.523:1): initialized
[    0.605337] Initialise system trusted keyring
[    0.612646] VFS: Disk quotas dquot_6.6.0
[    0.613177] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.615388] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.616703] NFS: Registering the id_resolver key type
[    0.617215] Key type id_resolver registered
[    0.617590] Key type id_legacy registered
[    0.618166] fuse init (API version 7.23)
[    0.624305] Key type asymmetric registered
[    0.624678] Asymmetric key parser 'x509' registered
[    0.625294] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.626139] io scheduler noop registered
[    0.626496] io scheduler deadline registered
[    0.626902] io scheduler cfq registered (default)
[    0.628895] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator
[    0.634418] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[    0.634996] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[    0.635562] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[    0.636130] rockchip-pcie f8000000.pcie: missing "memory-region" property
[    0.636732] PCI host bridge /pcie@f8000000 ranges:
[    0.637173]   MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[    0.637632]    IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[    1.138215] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[    1.138822] rockchip-pcie f8000000.pcie: deferred probe failed
[    1.139472] rockchip-pcie: probe of f8000000.pcie failed with error -110
[    1.141054] backlight supply power not found, using dummy regulator
[    1.142287] rk-vcodec ff650000.vpu_service: no regulator for vcodec
[    1.143213] rk-vcodec ff650000.vpu_service: probe device
[    1.143999] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
[    1.145356] rk-vcodec ff650000.vpu_service: could not find power_model node
[    1.145992] rk-vcodec ff650000.vpu_service: init success
[    1.146810] rk-vcodec ff660000.rkvdec: no regulator for vcodec
[    1.147807] rk-vcodec ff660000.rkvdec: probe device
[    1.148480] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
[    1.149440] rk-vcodec ff660000.rkvdec: could not find power_model node
[    1.150029] rk-vcodec ff660000.rkvdec: init success
[    1.151827] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.152509] dma-pl330 ff6d0000.dma-controller: 	DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[    1.154664] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.155341] dma-pl330 ff6e0000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.157378] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    1.158525] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud = 1500000) is a 16550A
[    1.159623] rockchip-pinctrl pinctrl: pin gpio4-19 already requested by fiq-debugger; cannot claim for ff1a0000.serial
[    1.160573] rockchip-pinctrl pinctrl: pin-147 (ff1a0000.serial) status -22
[    1.161190] rockchip-pinctrl pinctrl: could not request pin 147 (gpio4-19) from group uart2c-xfer  on device rockchip-pinctrl
[    1.162188] dw-apb-uart ff1a0000.serial: Error applying setting, reverse things back
[    1.163012] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 39, base_baud = 1500000) is a 16550A
[    1.164237] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 41, base_baud = 1500000) is a 16550A
[    1.165966] [drm] Initialized drm 1.1.0 20060810
[    1.169737] [drm] Rockchip DRM driver version: v1.0.1
[    1.172431] mali ff9a0000.gpu: Failed to get regulator
[    1.172887] mali ff9a0000.gpu: Power control initialization failed
[    1.173778] Unable to detect cache hierarchy for CPU 0
[    1.178717] brd: module loaded
[    1.184272] loop: module loaded
[    1.185085] zram: Added device: zram0
[    1.187758] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    1.188397] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    1.188900] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[    1.189427] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    1.190143] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    1.190761] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    1.196312] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    1.196910] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.197363]  Ring mode enabled
[    1.197635]  DMA HW capability register supported
[    1.198039]  Normal descriptors
[    1.198345]  RX Checksum Offload Engine supported (type 2)
[    1.198833]  TX Checksum insertion supported
[    1.199214]  Wake-Up On Lan supported
[    1.199577]  Enable RX Mitigation via HW Watchdog Timer
[    1.269561] libphy: stmmac: probed
[    1.269875] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[    1.270490] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[    1.272245] PPP generic driver version 2.4.2
[    1.272801] Rockchip WiFi SYS interface (V1.00) ... 
[    1.273358] usbcore: registered new interface driver asix
[    1.273879] usbcore: registered new interface driver ax88179_178a
[    1.274460] usbcore: registered new interface driver cdc_ether
[    1.276278] rockchip-dwc3 usb0: failed to get drvdata dwc3
[    1.280930] rockchip-dwc3 usb1: fail to get drvdata hcd
[    1.282409] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.283020] ehci-pci: EHCI PCI platform driver
[    1.283466] ehci-platform: EHCI generic platform driver
[    1.287736] ehci-platform fe3c0000.usb: EHCI Host Controller
[    1.288266] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    1.289054] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
[    1.294981] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    1.295669] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.296278] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.296910] usb usb1: Product: EHCI Host Controller
[    1.297351] usb usb1: Manufacturer: Linux 4.4.167 ehci_hcd
[    1.297841] usb usb1: SerialNumber: fe3c0000.usb
[    1.298711] hub 1-0:1.0: USB hub found
[    1.299085] hub 1-0:1.0: 1 port detected
[    1.299970] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.300532] ohci-platform: OHCI generic platform driver
[    1.301457] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    1.302076] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    1.302836] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
[    1.358112] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.358709] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.359362] usb usb2: Product: Generic Platform OHCI controller
[    1.359887] usb usb2: Manufacturer: Linux 4.4.167 ohci_hcd
[    1.360386] usb usb2: SerialNumber: fe3e0000.usb
[    1.361397] hub 2-0:1.0: USB hub found
[    1.361772] hub 2-0:1.0: 1 port detected
[    1.363758] usbcore: registered new interface driver cdc_acm
[    1.364277] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.365052] usbcore: registered new interface driver uas
[    1.365625] usbcore: registered new interface driver usb-storage
[    1.366284] usbcore: registered new interface driver usbserial
[    1.366833] usbcore: registered new interface driver usbserial_generic
[    1.367461] usbserial: USB Serial support registered for generic
[    1.368058] usbcore: registered new interface driver ch341
[    1.368578] usbserial: USB Serial support registered for ch341-uart
[    1.369189] usbcore: registered new interface driver cp210x
[    1.369709] usbserial: USB Serial support registered for cp210x
[    1.370313] usbcore: registered new interface driver ftdi_sio
[    1.370860] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.371648] usbcore: registered new interface driver option
[    1.372199] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.373016] usbcore: registered new interface driver pl2303
[    1.373537] usbserial: USB Serial support registered for pl2303
[    1.374130] usbcore: registered new interface driver qcserial
[    1.374672] usbserial: USB Serial support registered for Qualcomm USB modem
[    1.375796] mousedev: PS/2 mouse device common for all mice
[    1.377004] <<-GTP-INFO->> GTP driver installing
[    1.377857] sensor_register_slave:mma8452,id=17
[    1.378280] sensor_register_slave:lis3dh,id=7
[    1.378672] sensor_register_slave:mma7660,id=18
[    1.379088] sensor_register_slave:lsm303d,id=22
[    1.379492] sensor_register_slave:mpu6880_acc,id=24
[    1.379929] sensor_register_slave:mpu6500_acc,id=25
[    1.380377] sensor_register_slave:lsm330_acc,id=26
[    1.380804] sensor_register_slave:akm8975,id=30
[    1.381223] sensor_register_slave:akm8963,id=31
[    1.381626] sensor_register_slave:l3g4200d,id=45
[    1.382051] sensor_register_slave:l3g20d,id=46
[    1.382454] sensor_register_slave:ewtsa,id=47
[    1.382845] sensor_register_slave:lsm330_gyro,id=51
[    1.383297] sensor_register_slave:cm3217,id=53
[    1.383700] sensor_register_slave:cm3218,id=54
[    1.384589] i2c /dev entries driver
[    1.386569] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    1.387264] fan53555-reg: supplied by vcc3v3_sys
[    1.390261] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    1.390918] fan53555-reg: supplied by vcc3v3_sys
[    1.393849] rk808 0-001b: Pmic Chip id: 0x0
[    1.397897] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    1.398525] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    1.399231] DCDC_REG1: supplied by vcc3v3_sys
[    1.400573] DCDC_REG2: supplied by vcc3v3_sys
[    1.401656] DCDC_REG3: supplied by vcc3v3_sys
[    1.402417] DCDC_REG4: supplied by vcc3v3_sys
[    1.403352] LDO_REG1: supplied by vcc3v3_sys
[    1.404932] LDO_REG2: supplied by vcc3v3_sys
[    1.406375] LDO_REG3: supplied by vcc3v3_sys
[    1.407829] LDO_REG4: supplied by vcc3v3_sys
[    1.409297] LDO_REG5: supplied by vcc3v3_sys
[    1.410752] LDO_REG6: supplied by vcc3v3_sys
[    1.412236] LDO_REG7: supplied by vcc3v3_sys
[    1.413684] LDO_REG8: supplied by vcc3v3_sys
[    1.415166] SWITCH_REG1: supplied by vcc3v3_sys
[    1.415922] SWITCH_REG2: supplied by vcc3v3_sys
[    1.420003] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[    1.421030] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff8009578000
[    1.422770] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff800957a000
[    1.424252] rk3x-i2c ff120000.i2c: Initialized RK3xxx I2C bus at ffffff800957c000
[    1.425482] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff800957e000
[    1.427713] fusb302 4-0022: Can't get property of role, set role to default DRP
[    1.431448] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[    1.432675] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80095c2000
[    1.434460] IR NEC protocol handler initialized
[    1.439240] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
[    1.440241] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[    1.442249] device-mapper: uevent: version 1.0.3
[    1.442918] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    1.443846] Bluetooth: Virtual HCI driver ver 1.5
[    1.444387] Bluetooth: HCI UART driver ver 2.3
[    1.444787] Bluetooth: HCI UART protocol H4 registered
[    1.445255] Bluetooth: HCI UART protocol BCSP registered
[    1.445721] Bluetooth: HCI UART protocol LL registered
[    1.446190] Bluetooth: HCI UART protocol ATH3K registered
[    1.446669] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    1.447370] Bluetooth: HCI UART protocol BCM registered
[    1.447895] usbcore: registered new interface driver bfusb
[    1.448449] usbcore: registered new interface driver btusb
[    1.449409] cpu cpu0: bin=1
[    1.449707] cpu cpu0: leakage=15
[    1.450949] cpu cpu0: Failed to get pvtm
[    1.451365] cpu cpu0: bin-scale=34
[    1.451892] cpu cpu4: bin=1
[    1.452218] cpu cpu4: leakage=26
[    1.453197] cpu cpu4: Failed to get pvtm
[    1.453585] cpu cpu4: bin-scale=17
[    1.454863] cpu cpu0: avs=0, target-scale=34
[    1.455347] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[    1.457076] cpu cpu4: avs=0, target-scale=17
[    1.457511] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[    1.460050] sdhci: Secure Digital Host Controller Interface driver
[    1.460598] sdhci: Copyright(c) Pierre Ossman
[    1.461020] Synopsys Designware Multimedia Card Interface Driver
[    1.462502] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    1.463186] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    1.463789] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    1.464346] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    1.465224] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.465982] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[    1.466529] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[    1.467876] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[    1.468570] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[    1.469183] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[    1.469726] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
[    1.470594] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.471694] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.472377] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.484017] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.495001] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.495658] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[    1.496358] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[    1.497207] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.499328] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[    1.499854] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[    1.527066] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    1.529140] ledtrig-cpu: registered to indicate activity on CPUs
[    1.529754] hidraw: raw HID events driver (C) Jiri Kosina
[    1.530669] usbcore: registered new interface driver usbhid
[    1.531187] usbhid: USB HID core driver
[    1.532635] rockchip-dmc dmc: unable to get devfreq-event device : dfi
[    1.536376] rt5651 1-001a: Device with ID register 0xffffffc0 is not rt5651
[    1.541039] NET: Registered protocol family 10
[    1.542289] NET: Registered protocol family 17
[    1.542790] Bluetooth: RFCOMM TTY layer initialized
[    1.543249] Bluetooth: RFCOMM socket layer initialized
[    1.543716] Bluetooth: RFCOMM ver 1.11
[    1.544079] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.544608] Bluetooth: HIDP socket layer initialized
[    1.545110] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    1.545798] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    1.546265] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6212
[    1.546871] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    1.547512] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    1.548231] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
[    1.549036] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    1.549675] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    1.550153] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    1.550611] [BT_RFKILL]: Enter rfkill_rk_init
[    1.551414] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
[    1.552172] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
[    1.552888] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
[    1.553609] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
[    1.554774] [BT_RFKILL]: Request irq for bt wakeup host
[    1.555338] [BT_RFKILL]: ** disable irq
[    1.555817] [BT_RFKILL]: bt shut off power
[    1.571523] mmc1: MAN_BKOPS_EN bit is not set
[    1.577015] [BT_RFKILL]: bt_default device registered.
[    1.577567] Key type dns_resolver registered
[    1.578335] sensor_register_slave:mpu6880_gyro,id=50
[    1.579659] 1-0036 supply avdd not found, using dummy regulator
[    1.580301] 1-0036 supply dovdd not found, using dummy regulator
[    1.580897] 1-0036 supply dvdd not found, using dummy regulator
[    1.582806] mmc1: new HS200 MMC card at address 0001
[    1.583497] ov4689 1-0036: Unexpected sensor id(000000), ret(-5)
[    1.584280] ov4689: probe of 1-0036 failed with error -5
[    1.584515] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB 
[    1.585453] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
[    1.586009] 2-0036 supply avdd not found, using dummy regulator
[    1.586094] 2-0036 supply dovdd not found, using dummy regulator
[    1.586169] 2-0036 supply dvdd not found, using dummy regulator
[    1.587875] ov4689 2-0036: Unexpected sensor id(000000), ret(-5)
[    1.588178] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
[    1.588609] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB
[    1.589187]      uboot: 0x000400000 -- 0x000800000 (4 MB)
[    1.589192]      trust: 0x000800000 -- 0x000c00000 (4 MB)
[    1.589197]       misc: 0x000c00000 -- 0x001000000 (4 MB)
[    1.589201]   resource: 0x001000000 -- 0x001c00000 (12 MB)
[    1.589206]     kernel: 0x001c00000 -- 0x003c00000 (32 MB)
[    1.589210]       boot: 0x003c00000 -- 0x005c00000 (32 MB)
[    1.589215]     rootfs: 0x006000000 -- 0x11cc00000 (4460 MB)
[    1.589219]   userdata: 0x11cc00000 -- 0x3a3a00000 (10350 MB)
[    1.593664]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8
[    1.593664] ov4689: probe of 2-0036 failed with error -5
[    1.595315] 1-0010 supply avdd not found, using dummy regulator
[    1.595895] 1-0010 supply dovdd not found, using dummy regulator
[    1.596492] 1-0010 supply dvdd not found, using dummy regulator
[    1.598849] ov13850 1-0010: Unexpected sensor id(000000), ret(-5)
[    1.599581] ov13850: probe of 1-0010 failed with error -5
[    1.600480] 2-0010 supply avdd not found, using dummy regulator
[    1.601071] 2-0010 supply dovdd not found, using dummy regulator
[    1.601653] 2-0010 supply dvdd not found, using dummy regulator
[    1.604144] ov13850 2-0010: Unexpected sensor id(000000), ret(-5)
[    1.604850] ov13850: probe of 2-0010 failed with error -5
[    1.606082] Registered cp15_barrier emulation handler
[    1.606644] Registered setend emulation handler
[    1.608112] registered taskstats version 1
[    1.608489] Loading compiled-in X.509 certificates
[    1.609611] rga2: Module initialized.
[    1.611293] phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator
[    1.614003] rockchip-drm display-subsystem: defer getting devfreq
[    1.614934] rockchip-vop ff900000.vop: missing rockchip,grf property
[    1.615882] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008bd7010)
[    1.616654] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[    1.617473] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008bd7010)
[    1.618473] rockchip-dp ff970000.edp: no DP phy configured
[    1.619683] i2c i2c-9: of_i2c: modalias failure on /edp@ff970000/ports
[    1.620423] rockchip-drm display-subsystem: bound ff970000.edp (ops 0xffffff8008bce878)
[    1.621473] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.624125] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008bcc190)
[    1.625622] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
[    1.626624] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff8008bcd148)
[    1.627458] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
[    1.628254] cdn-dp fec00000.dp: Falling back to user helper
[    1.628370] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.628372] [drm] No driver support for vblank timestamp query.
[    1.669623] rockchip-drm display-subsystem: can't not find any loader display
[    1.670301] rockchip-drm display-subsystem: failed to show loader logo
[    1.671422] Freeing drm_logo memory: 2252K
[    1.720882] rockchip-vop ff900000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 14
[    1.721543] rockchip-vop ff8f0000.vop: [drm:vop_crtc_enable] Update mode to 1920x1080p60, type: 11
[    1.728183] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.728561] rockchip-dp ff970000.edp: Rx Max Link Rate is abnormal :0 !
[    1.728565] rockchip-dp ff970000.edp: Rx Max Lane count is abnormal :0 !
[    1.731020] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.731024] rockchip-dp ff970000.edp: LT link start failed!
[    1.731029] rockchip-dp ff970000.edp: eDP link training failed (-110)
[    1.733919] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.734310] rockchip-dp ff970000.edp: LT link start failed!
[    1.734314] rockchip-dp ff970000.edp: eDP link training failed (-121)
[    1.736939] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.739772] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.739776] rockchip-dp ff970000.edp: LT link start failed!
[    1.739780] rockchip-dp ff970000.edp: eDP link training failed (-110)
[    1.742701] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.743085] rockchip-dp ff970000.edp: LT link start failed!
[    1.743089] rockchip-dp ff970000.edp: eDP link training failed (-121)
[    1.745705] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.748540] rockchip-dp ff970000.edp: AUX CH command reply failed!
[    1.748544] rockchip-dp ff970000.edp: LT link start failed!
[    1.748548] rockchip-dp ff970000.edp: eDP link training failed (-110)
[    1.748676] rockchip-dp ff970000.edp: unable to do link train
[    1.840307] Console: switching to colour frame buffer device 240x67
[    1.938837] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.946887] mali ff9a0000.gpu: leakage=19
[    1.950363] mali ff9a0000.gpu: Failed to get pvtm
[    1.951977] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
[    1.952778] mali ff9a0000.gpu: Protected mode not available
[    1.953720] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[    1.954437] mali ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallback mali-simple-power-model
[    1.955533] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 414; [Func] : kbase_devfreq_init(); success initing power_model_simple.
[    1.957790] mali ff9a0000.gpu: Probed as mali0
[    1.962564] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    1.963079] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[    1.963879] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
[    1.964685] xhci-hcd xhci-hcd.8.auto: irq 232, io mem 0xfe800000
[    1.965438] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    1.966046] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.966680] usb usb3: Product: xHCI Host Controller
[    1.967115] usb usb3: Manufacturer: Linux 4.4.167 xhci-hcd
[    1.967599] usb usb3: SerialNumber: xhci-hcd.8.auto
[    1.968699] hub 3-0:1.0: USB hub found
[    1.969090] hub 3-0:1.0: 1 port detected
[    1.969671] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    1.970175] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[    1.970903] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.971689] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    1.972298] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.972931] usb usb4: Product: xHCI Host Controller
[    1.973382] usb usb4: Manufacturer: Linux 4.4.167 xhci-hcd
[    1.973875] usb usb4: SerialNumber: xhci-hcd.8.auto
[    1.974811] hub 4-0:1.0: USB hub found
[    1.975230] hub 4-0:1.0: 1 port detected
[    1.976823] xhci-hcd xhci-hcd.8.auto: remove, state 1
[    1.977305] usb usb4: USB disconnect, device number 1
[    1.996915] xhci-hcd xhci-hcd.8.auto: Host not halted after 16000 microseconds.
[    1.997561] xhci-hcd xhci-hcd.8.auto: Host controller not halted, aborting reset.
[    1.998262] xhci-hcd xhci-hcd.8.auto: USB bus 4 deregistered
[    1.998763] xhci-hcd xhci-hcd.8.auto: remove, state 1
[    1.999229] usb usb3: USB disconnect, device number 1
[    2.000278] xhci-hcd xhci-hcd.8.auto: USB bus 3 deregistered
[    2.089698] vendor storage:20160801 ret = 0
[    2.640383] phy phy-ff770000.syscon:usb2-phy@e450.7: charger = USB_FLOATING_CHARGER
[    2.648019] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.648547] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 3
[    2.649498] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
[    2.650382] xhci-hcd xhci-hcd.9.auto: irq 233, io mem 0xfe900000
[    2.651425] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.652074] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.652720] usb usb3: Product: xHCI Host Controller
[    2.653190] usb usb3: Manufacturer: Linux 4.4.167 xhci-hcd
[    2.653683] usb usb3: SerialNumber: xhci-hcd.9.auto
[    2.655778] hub 3-0:1.0: USB hub found
[    2.656247] hub 3-0:1.0: 1 port detected
[    2.657308] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.657836] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4
[    2.658725] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.659705] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.660372] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.661042] usb usb4: Product: xHCI Host Controller
[    2.661489] usb usb4: Manufacturer: Linux 4.4.167 xhci-hcd
[    2.662011] usb usb4: SerialNumber: xhci-hcd.9.auto
[    2.664235] hub 4-0:1.0: USB hub found
[    2.664643] hub 4-0:1.0: 1 port detected
[    2.670769] ehci-platform fe380000.usb: EHCI Host Controller
[    2.671371] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
[    2.672313] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
[    2.678224] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    2.679273] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.679887] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.680577] usb usb5: Product: EHCI Host Controller
[    2.681048] usb usb5: Manufacturer: Linux 4.4.167 ehci_hcd
[    2.681541] usb usb5: SerialNumber: fe380000.usb
[    2.683656] hub 5-0:1.0: USB hub found
[    2.684103] hub 5-0:1.0: 1 port detected
[    2.686318] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    2.686955] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
[    2.688018] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
[    2.743577] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.744231] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.744878] usb usb6: Product: Generic Platform OHCI controller
[    2.745441] usb usb6: Manufacturer: Linux 4.4.167 ohci_hcd
[    2.745935] usb usb6: SerialNumber: fe3a0000.usb
[    2.748165] hub 6-0:1.0: USB hub found
[    2.748571] hub 6-0:1.0: 1 port detected
[    2.750615] input: adc-keys as /devices/platform/adc-keys/input/input0
[    2.754374] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[    2.755112] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[    2.755732] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[    2.756388] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[    2.757307] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    2.758142] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[    2.758724] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[    2.760058] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[    2.771177] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.783397] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
[    2.785299] rockchip-dmc dmc: Failed to get leakage
[    2.785855] rockchip-dmc dmc: Failed to get pvtm
[    2.787132] rockchip-dmc dmc: failed to get vop pn to msch rl
[    2.788020] rockchip-dmc dmc: could not find power_model node
[    2.804073] devfreq dmc: Couldn't update frequency transition information.
[    2.806939] asoc-simple-card hdmi-sound: i2s-hifi <-> ff8a0000.i2s mapping ok
[    2.811211] asoc-simple-card spdif-sound: dit-hifi <-> ff870000.spdif mapping ok
[    2.814696] input: gpio-keys as /devices/platform/gpio-keys/input/input1
[    2.816715] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:05 UTC (1358499005)
[    2.826885] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[    2.828929] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.830980] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.834250] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[    2.838155] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
[    2.844907] vcc_sd: disabling
[    2.846530] ALSA device list:
[    2.846801]   #0: rockchip,hdmi
[    2.847103]   #1: ROCKCHIP,SPDIF
[    2.848263] Freeing unused kernel memory: 1088K
Loading, please wait...
starting version 237
[    2.927748] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    2.930889] mmc2: new high speed SDIO card at address 0001
[    3.126801] cdn-dp fec00000.dp: [drm:cdn_dp_request_firmware] *ERROR* failed to request firmware: -11
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[    3.251873] EXT4-fs (mmcblk1p7): mounted filesystem with ordered data mode. Opts: (null)
Begin: Will now check userdata file system ... fsck from util-linux 2.31.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk1p8] fsck.ext4 -a -C0 /dev/mmcblk1p8 
userdata: recovering journal
userdata: Superblock last mount time is in the future.
	(by less than a day, probably due to the hardware clock being incorrectly set)
userdata: clean, 31558/518400 files, 1349961/2649600 blocks
done.
[    3.322079] EXT4-fs (mmcblk1p8): mounted filesystem with ordered data mode. Opts: (null)
[    3.326273] EXT4-fs (mmcblk1p8): re-mounted. Opts: data=ordered
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    3.529147] systemd[1]: System time before build time, advancing clock.
[    3.557650] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.564067] cgroup: cgroup2: unknown option "nsdelegate"
[    3.582309] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    3.585630] systemd[1]: Detected architecture arm64.

Welcome to Ubuntu 18.04.3 LTS!

[    3.606467] systemd[1]: Set hostname to <NanoPi-NEO4>.
[    3.739775] systemd[1]: File /lib/systemd/system/systemd-udevd.service:34 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    3.741326] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    3.835589] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
[    3.836866] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary Executab…rmats File System Automount Point.
[    3.838370] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
[    3.841583] systemd[1]: Created slice System Slice.
[  OK  ] Created slice System Slice.
[    3.842748] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
[    3.843720] systemd[1]: Listening on Journal Audit Socket.
[  OK  ] Listening on Journal Audit Socket.
[    3.844392] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
[    3.845723] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    3.846342] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
[    3.850213] systemd[1]: Starting Nameserver information manager...
         Starting Nameserver information manager...
[    3.854190] random: systemd: uninitialized urandom read (16 bytes read, 69 bits of entropy available)
[    3.861198] systemd[1]: Starting Load Kernel Modules...
         Starting Load Kernel Modules...
[    3.863456] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
[    3.868189] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[    3.885474] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
[    3.886549] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    3.887493] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
[    3.892019] systemd[1]: Starting Create list of required static device nodes for the current kernel...
         Starting Create list of required st…ce nodes for the current kernel...
[    3.893558] random: systemd: uninitialized urandom read (16 bytes read, 71 bits of entropy available)
[    3.894858] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    3.899483] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[    3.901082] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    3.906138] systemd[1]: Starting udev Coldplug all Devices...
         Starting udev Coldplug all Devices...
[    3.908522] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[    3.909431] systemd[1]: Reached target Slices.
[  OK  ] Reached target Slices.
[    3.910547] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    3.910907] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.910914] Bluetooth: BNEP filters: protocol multicast
[    3.910940] Bluetooth: BNEP socket layer initialized
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[    3.912938] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    3.917876] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[    3.918996] usbcore: registered new interface driver cdc_wdm
[    3.923285] systemd[1]: Starting Remount Root and Kernel File Systems...
[    3.923396] usbcore: registered new interface driver simcom_qmi_wwan
         Starting Remount Root and Kernel File Systems...
[    3.925550] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[    3.930105] systemd[1]: Starting Set the console keyboard layout...
         Starting Set the console keyboard layout...
[    3.931466] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
[    3.932619] systemd[1]: Reached target Local Encrypted Volumes.
[  OK  ] Reached target Local Encrypted Volumes.
[    3.933707] systemd[1]: Reached target Paths.
[  OK  ] Reached target Paths.
[    3.935945] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[    3.936916] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    3.944271] systemd[1]: Started Load Kernel Modules.
[  OK  ] Started Load Kernel Modules.
[    3.945991] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Mounted POSIX Message Queue File System.
[    3.948896] systemd[1]: Started Create list of required static device nodes for the current kernel.
[  OK  ] Started Create list of required sta…vice nodes for the current kernel.
[    3.950708] systemd[1]: Mounted Kernel Debug File System.
[  OK  ] Mounted Kernel Debug File System.
[    3.957573] systemd[1]: Starting Create Static Device Nodes in /dev...
         Starting Create Static Device Nodes in /dev...
[    3.963132] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[    3.968505] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[    3.973902] systemd[1]: Mounting Kernel Configuration File System...
         Mounting Kernel Configuration File System...
[    3.977240] systemd[1]: Started Remount Root and Kernel File Systems.
[  OK  ] Started Remount Root and Kernel File Systems.
[    3.982405] systemd[1]: Started Nameserver information manager.
[  OK  ] Started Nameserver information manager.
[    3.985843] systemd[1]: Mounted FUSE Control File System.
[  OK  ] Mounted FUSE Control File System.
[    3.986815] systemd[1]: Mounted Kernel Configuration File System.
[  OK  ] Mounted Kernel Configuration File System.
[    3.988430] systemd[1]: Reached target Network (Pre).
[  OK  ] Reached target Network (Pre).
[    3.992292] systemd[1]: Starting Load/Save Random Seed...
         Starting Load/Save Random Seed...
[    4.045478] systemd[1]: Started Create Static Device Nodes in /dev.
[  OK  ] Started Create Static Device Nodes in /dev.
[    4.054729] systemd[1]: Starting udev Kernel Device Manager...
         Starting udev Kernel Device Manager...
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Journal Service.
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Set the console keyboard layout.
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting Raise network interfaces...
         Starting Set console font and keymap...
[  OK  ] Started Set console font and keymap.
[  OK  ] Created slice system-systemd\x2dbacklight.slice.
         Starting Load/Save Screen Backlight…ightness of backlight:backlight...
[  OK  ] Started Flush Journal to Persistent Storage.
         Starting Create Volatile Files and Directories...
[  OK  ] Found device /dev/ttyFIQ0.
[  OK  ] Reached target Sound Card.
[  OK  ] Started Load/Save Screen Backlight Brightness of backlight:backlight.
[    4.516406] rockchip-mipi-dphy-rx ff770000.syscon:mipi-dphy-rx0: invalid resource
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
         Starting Network Time Synchronization...
[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
         Starting Load/Save RF Kill Switch Status...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started Load/Save RF Kill Switch Status.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on UUID daemon activation socket.
[  OK  ] Started Discard unused blocks once a week.
[  OK  ] Started Daily apt download activities.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Listening on GPS (Global Positioning System) Daemon Sockets.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Listening on D-Bus System Message Bus Socket.
         Starting Docker Socket for the API.
[  OK  ] Started Message of the Day.
[  OK  ] Reached target Timers.
[  OK  ] Listening on Docker Socket for the API.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
         Starting Initialize hardware monitoring sensors...
[  OK  ] Started Set the CPU Frequency Scaling governor.
         Starting Login Service...
[  OK  ] Started D-Bus System Message Bus.
         Starting LSB: Load kernel modules needed to enable cpufreq scaling...
         Starting LSB: Start busybox udhcpd at boot time...
         Starting Save/Restore Sound Card State...
         Starting brcm_patchram_plus...
[  OK  ] Started Regular background program processing daemon.
         Starting WPA supplicant...
         Starting Dispatcher daemon for systemd-networkd...
         Starting HDMI-force-ON...
         Starting Restore /etc/resolv.conf i…fore the ppp link was shut down...
[  OK  ] Started brcm_patchram_plus.
[  OK  ] Started Initialize hardware monitoring sensors.
[  OK  ] Found device /sys/subsystem/net/devices/eth0.
[  OK  ] Started Save/Restore Sound Card State.
[  OK  ] Started HDMI-force-ON.
[  OK  ] Started Restore /etc/resolv.conf if…before the ppp link was shut down.
[  OK  ] Started Login Service.
[  OK  ] Started LSB: Start busybox udhcpd at boot time.
[  OK  ] Started WPA supplicant.
[  OK  ] Started ifup for eth0.
         Starting Bluetooth service...
[  OK  ] Found device /sys/subsystem/net/devices/wlan0.
[  OK  ] Started ifup for wlan0.
[  OK  ] Started Bluetooth service.
         Starting Hostname Service...
[  OK  ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
         Starting LSB: set CPUFreq kernel parameters...
[  OK  ] Started LSB: set CPUFreq kernel parameters.
[  OK  ] Started Hostname Service.
[    6.713202] CONFIG-ERROR) dhd_conf_set_bufiovar: country setting failed -2
[  OK  ] Started Dispatcher daemon for systemd-networkd.
[  OK  ] Started Raise network interfaces.
[  OK  ] Reached target Network.
         Starting Advanced IEEE 802.11 AP an…2.1X/WPA/WPA2/EAP Authenticator...
[  OK  ] Reached target Network is Online.
         Starting LSB: Brings up/down network automatically...
         Starting LSB: disk temperature monitoring daemon...
         Starting containerd container runtime...
[  OK  ] Started Simcom Modem wwan network manager.
         Starting Permit User Sessions...
         Starting /etc/rc.local Compatibility...
         Starting dnsmasq - A lightweight DHCP and caching DNS server...
         Starting OpenBSD Secure Shell server...
[  OK  ] Started Unattended Upgrades Shutdown.
[  OK  ] Started Battery charger and PM server.
         Starting vsftpd FTP server...
[  OK  ] Started Permit User Sessions.
[  OK  ] Started vsftpd FTP server.
[   24.445573] rc.local[758]: bcm43xx_init
[   24.447077] rc.local[758]: Set Controller UART speed to 115200 bit/s
[   24.448599] rc.local[758]: Flash firmware /etc/firmware/BCM43430A1.hcd
[   24.449849] rc.local[758]: Set Controller UART speed to 115200 bit/s
[   24.451111] rc.local[758]: Device setup complete
[   24.458760] rc.local[758]: No ttyUSB port found

Ubuntu 18.04.3 LTS NanoPi-NEO4 ttyFIQ0

